• Sourcing Solutions
  • Services & Membership
  • Help & Community
AMT Pump 282B-98 Self-Priming Centrifugal Pump, Cast Stainless Steel, 2 HP, 3 Phase, 230/460V, Curve C, 1-1/2" NPT Female Suction & Discharge Ports

AMT Pump 282B-98 Self-Priming Centrifugal Pump, Cast Stainless Steel, 2 HP, 3 Phase, 230/460V, Curve C, 1-1/2" NPT Female Suction & Discharge Ports

Shared by: Kimora Boys from AMAZON
Over 829 suppliers can give you a quotation.
Get Quotations Now
You should get the quotation(s) in 5 hours .

This AMT 282B-98 stainless steel self-priming centrifugal pump has a 2 hp, 3 phase, 230/460V TEFC electric motor and 1-1/2" female NPT suction and discharge ports. This pump has C curve performance with a 100 gallons per minute (gpm) maximum flow rate and 97 feet maximum vertical lift at 3,450 RPM. The pump is self-priming to 20 vertical feet (after initial fill) with its built-in check valve, and its clog-resistant impeller handles semi-solids up to 3/8" diameter. The 300 series cast stainless steel pump housing has Viton (FKM, fluoroelastomer) mechanical seal and O-ring, a fill and drain plug for easy servicing, and a double volute chamber for reduced radial load on the impeller. The motor enclosure is TEFC (totally enclosed, fan cooled) for protection from dust and indirect water spray and complies with National Electrical Manufacturers Association (NEMA) 56J standard for mounting dimensions. This portable pump is suitable for use in applications such as waste water drainage and processing.

Motor 2 hp, 230/460V, 6/3 amp, 3 phase, TEFC Pump Centrifugal self-priming with dual volute Maximum flow rate 100 gpm Impeller Stainless steel self-cleaning, semi-open Suction port 1-1/2" NPT Discharge port 1-1/2" NPT Maximum operating temperature 200 degrees F Standards met NEMA 56J Dimensions* 18.5/47.0** x 9.1/23.1** x 9.9/25.4 (L x W x H) inches/centimeters

* L is length, the horizontal distance from front to back; W is width, the horizontal distance from left to right; H is height, the vertical distance from lowest to highest point

**This measurement may vary due to motor manufacturer's specifications

Pumps use mechanical action to move liquids, gases, or slurries (solids suspended in a liquid or gas). The mechanical action is categorized as either positive displacement (PD) or kinetic. PD pumps capture and release discrete amounts of flow into a chamber and then force it out. Some examples of PD pumps are fuel and oil pumps in cars, pumps in hydraulic systems, and bicycle pumps. Kinetic pumps move liquids, gases, or slurries by transferring energy from the pump's movement to the flow. They use an impeller to draw the flow in, add energy to the flow, and move it through a volute (a spiral funnel through which the flow moves), and into the system. Some examples of kinetic pumps include centrifugal (the most common pump in industrial applications), in-line pumps, sump pumps, and suction pumps. Energy sources for all types of pumps include wind power, manual operation, electricity, and gasoline or diesel fuel.

American Machine and Tool (AMT) manufactures centrifugal and diaphragm pumps. The company is headquartered in Royersford, PA.

Notice:The articles, pictures, news, opinions, videos, or information posted on this webpage (excluding all intellectual properties owned by Alibaba Group in this webpage) are uploaded by registered members of Alibaba. If you are suspect of any unauthorized use of your intellectual property rights on this webpage, please report it to us at the following:ali-guide@service.alibaba.com.